Gas & Electric Heating Teppanyaki Grill Table Operating Instructions
Electric heating Teppanyaki Grill Table operating instructions
1. First turn on the fan power of the Teppanyaki grill table, check the exhaust system, and then proceed to the next step after it is normal. You can also temporarily turn off the smoke exhaust fan and turn it on again when it is actually in operation.
2. Then turn on the power switch, the power indicator lights, press the heating start button, the heating tube starts to work until the temperature reaches the set upper limit and stops. Finally, the heating element of the equipment will work under the control of digital temperature control between the upper and lower temperature limits.
3. The temperature control setting process: First, turn on the power switch, the power light is on, and start to start, press SET for 0.5 seconds, the screen displays CC.
Note: 1. The value of Lock is 0 for unlocking, 1 is for locking, and the others are factory settings, and changes are strictly prohibited.
2. The upper limit of PH temperature is strictly prohibited to exceed 380℃.
3. Set CC as the difference between the upper and lower limits, (that is, the upper limit minus the lower limit).
4. Set P to 0.
5. SV is set to the required value minus 1/2CC value.
Example: The upper limit is 100°C and the lower limit is 80°C.
Set CC to 20°C, P to 0, and SV to 90°C. The instrument stops working when it reaches 100°C, and starts working when it reaches 80°C.
Gas Teppanyaki Grill Table Operating Instructions
1. Turn on the fan power first, check the exhaust system, and then proceed to the next step when it is normal.
2. Then turn on the gas switch and do not turn it on when igniting.
3. Use the ignition rod to ignite again, do not open the ignition rod switch, and then turn it on after ignition.
4. Use the ignition rod to ignite the burner. (Because the air contained in the pipeline at the beginning of the ignition, the ignition may not be smooth, just continue to ignite.)
5. Finally adjust the size of the gas switch to an appropriate state to control the burner flame intensity.
Teppanyaki equipment structure description
1. Working principle: heating the iron plate to the working temperature by heating with gas (gas, liquefied gas, natural gas) or using an aluminum heating plate, the temperature of the iron plate is controlled by a gas switch or a digital temperature controller, and the amount of air extraction is controlled by an air valve .
2. Air consumption:
Gas type: gas: 2.92m3/Hr
Liquefied gas: 0.98kg/Hr
Natural gas: 1.2m3/Hr
Electric heating: voltage: 380V power: 6KW
3. Iron plate material: The iron plate is made of imported alloy steel. The iron plate is ground by a surface grinder and has a thickness of 20mm. The material is not deformed and does not change color.
4. Exhaust air requirement: air volume of 2000m3/Hr/set, wind speed of 12m/s can be connected to the outdoor, depending on the specific situation. (Refer to the schematic diagram of the air duct direction)
5. Internal structure:
A. Main heating system: gas: 18 duckbill burners, the temperature of the teppanyaki is controlled by a gas switch, and the main heating range is 500mm×500mm.
B. Thermal insulation system: The area other than the main heat is the thermal insulation system, its temperature is controlled below 100 degrees, and the humanized design avoids the hidden safety hazards caused by customers curiously touching the iron plate.
C. Fire prevention system: the function of preventing the open flame from entering the exhaust duct, and eliminating the hidden dangers caused by the open flame.
D. Exhaust gas treatment system: make the exhaust gas in the equipment circulate and discharge normally.
E. Oil fume treatment system: The oil fume separation system inside the equipment can prevent the internal oil fume from dropping into the exhaust duct and dropping directly in the oil collection drawer.
6. The external decoration of the equipment can be decorated according to the style and grade of the interior decoration of the store or made by our company. The decorative table can be imported black gold sand marble or tempered glass (gold sand on the reverse side), ebony wood or black walnut wood decoration.
